Tool Setter
-
Manufacturing / Production
-
Trades / Skilled Labor
Job Description & How to Apply Below
Position Summary
The HPDC Tooling Setup Technician is responsible for the safe and efficient installation, removal, setup, and changeover of dies and related tooling used in High Pressure Die Casting (HPDC) operations.
This position ensures dies, tooling, cooling systems, hydraulic connections, ejector systems, and related equipment are properly installed and prepared for production. The Tooling Setup Technician works closely with Production, Tooling, Maintenance, Process Engineering, and Quality to minimize changeover time, support successful production startups, and maintain safe and reliable die casting operations.
Essential Duties and Responsibilities
Perform complete die changes and tooling setups on HPDC machines according to production schedules and established procedures.
Safely remove dies from die casting machines and install dies required for upcoming production runs.
Use overhead cranes, hoists, lifting devices, and rigging equipment to safely move and position dies and tooling.
Verify proper die orientation, positioning, alignment, clamping, and machine interface before startup.
Install and connect die-related components, including cooling and heating lines, water manifolds, hydraulic lines, core-pull connections, lubrication systems, sensors, switches, and other required connections.
Connect and verify ejector systems, slides, cores, and other moving tooling components.
Inspect dies and tooling before installation for visible damage, wear, leaks, loose components, blocked lines, or other conditions that could affect safe operation or production.
Verify that cooling circuits, water lines, fittings, hoses, seals, and connections are properly installed and free from leaks.
Install or assist with setup of shot-end components and other tooling-related equipment as required.
Assist with setup and alignment of trim dies, trim presses, fixtures, and related downstream tooling as required.
Verify that required die sprays, lubricants, release agents, and tooling supplies are available and properly connected.
Follow setup sheets, work instructions, tooling specifications, production schedules, and engineering requirements.
Complete pre-startup inspections and setup verification before releasing equipment for production.
Support machine startup and first-piece production following die changes.
Work with Process Engineering and Production to resolve setup-related issues during startup.
Assist Quality personnel with first-piece or first-article approval as required.
Troubleshoot basic tooling and setup issues involving alignment, connections, cooling, ejector operation, core pulls, sensors, and related components.
Immediately identify and communicate damaged or malfunctioning dies and tooling to Tooling, Maintenance, Engineering, or supervision.
Assist Tool & Die personnel with minor tooling adjustments and repairs when qualified and assigned.
Maintain dies, setup equipment, rigging equipment, hoses, fittings, clamps, and tooling accessories in clean and serviceable condition.
Return removed dies and tooling to designated storage or maintenance locations.
Maintain accurate die-change, setup, inspection, and tooling documentation as required.
Participate in activities to reduce die-change and setup times and improve equipment availability.
Support SMED, 5S, continuous improvement, and standardized work initiatives.
Maintain a clean, organized, and safe work area.
Follow all company safety, quality, environmental, and operating procedures.
Perform other related duties as assigned.
Safety Responsibilities
Follow Lockout/Tagout (LOTO) and stored-energy-control procedures during tooling changes and equipment setup.
Follow established crane, hoist, rigging, and material-handling procedures.
Inspect lifting devices and rigging equipment before use as required.
Never work beneath suspended loads.
Follow appropriate procedures when working around hot dies, molten metal, hydraulic systems, compressed air, and other hazardous energy sources.
Wear required personal protective equipment (PPE).
Immediately report unsafe conditions, damaged lifting equipment, tooling problems, leaks, and other safety concerns.
Required Qualifications
Previous experience in manufacturing, tooling, machine setup, die casting, mold setup, or a related industrial environment.
Strong mechanical aptitude and ability to work with large industrial equipment.
Ability to safely use hand tools, power tools, torque tools, and basic measuring equipment.
Ability to read and follow setup…
(If this job is in fact in your jurisdiction, then you may be using a Proxy or VPN to access this site, and to progress further, you should change your connectivity to another mobile device or PC).
View / Apply for Jobs
Matching My Jurisdiction