METALS Inspector Security Clearance

Position: METALS INSPECTOR with Security Clearance
Duties
* You will arrange for correction of deficiencies and re-inspection of repaired items.
* You will perform traditional, Non-Destructive Inspection (NDI) of castings, forgings, machined parts, test plates, welds, metal cladding, pipes, bar stock, flat metal sheets, airframe and engine assemblies utilizing NDI test equipment.
* You will inspect parts for flaws or defects, discontinuities in patterns, interpret indications and document flaws or defects in material and prepare reports on defective parts.
* You will work with subordinate inspectors to set the pace and demonstrate proper inspection methods and may be required to work with trainees. Requirements Conditions of employment
* Must be a US Citizen.
* Must be determined suitable for federal employment.
* Must participate in the direct deposit pay program.
* New employees to the Department of the Navy will be required to successfully pass the E-Verify employment verification check. To learn more about E-Verify, including your rights and responsibilities, visit e-verify.gov
* Within the Department of Defense (DoD), the appointment of retired military members within 180 days immediately following retirement date to a civilian position is subject to the provisions of 5 United States Code 3326.
* Males born after 12-31-59 must be registered for Selective Service.
* This is a bargaining unit position.
* You will be required to successfully complete a pre-appointment physical examination.
* You will be required to obtain and maintain an interim and/or final security clearance prior to entrance on duty. Failure to obtain and maintain the required level of clearance may result in the withdrawal of a job offer or removal.
* Successful completion of a pre-employment drug test (including marijuana) is required. A tentative offer of employment will be rescinded if you fail to report to the drug test appointment or fail the test. You will be subject to random testing.
* You will be required to wear personal protective equipment such as helmets, gloves, coveralls, glasses, goggles, respirators and safety shoes continuously for the duration of the work shift.
* Work is performed in areas where potentially harmful physical and chemical agents are present (e.g. fumes, dust, heat, ionizing and non-ionizing radiation and chemicals). You will be required to participate in medical surveillance programs.
* This position may require travel from normal duty station to CONUS and OCONUS and may include remote or isolated sites. You must be able to travel on military and commercial aircraft for extended periods of time.
* You must have a certificate of completion and will be required to pass level II certification exams and maintain level II certification in at least two (2) of the following methods: (ET),(MT), (PT), (UT), X-Ray, (TE).
* Hearing protection must be worn for noise levels of 85 DBA and double protection is required for levels over 105 OBA.
* This position requires corrected vision as eye strain may occur from prolonged work on small parts, near vision correctable at 14" to Jaeger 2 and far vision correctable to 20/20 in one eye. You must be able to distinguish color. Qualifications Although a specific length of time and experience is not required for most trade and labor occupations, you must show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying.

Qualification requirements emphasis is on quality of experience, not necessarily the length of time. Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the job elements and screen out listed below. This job has a screen-out element which will be used to determine minimum eligibility for this job. The Screen-out Element is: The ability to perform the work of the position without more than normal supervision including:1) Reading and interpreting specifications, sketches, blueprints, and technical directives to accurately understand shop orders or products required for testing and evaluation;
2) Applying mathematical equations and formulas relevant to non-destructive inspection (NDI) methods;
3)
Operating NDI equipment with the proficiency needed to perform general maintenance and minor repairs, including replacing probe, cables and conducting periodic inspections; and
4) Calibrating and setting up nondestructive testing equipment prior to examining parts, components or assemblies to ensure optimal performance and accurate examination results. Applicants must meet the requirements of the Office of Personnel Management (OPM) Job Qualification Handbook for Trades and Labor Occupations. Additional qualification information can be found at:
Experience refers to paid and unpaid experience, including volunteer work done through National Service programs (e.g., professional, philanthropic, religious, spiritual, community, student,…