Mechatronics Engineer
Job in
Los Angeles, Los Angeles County, California, 90001, USA
Listing for:
SunAlgo
Full Time
position
Listed on 2026-11-06
Job specializations:
-
Software Development
Job Description & How to Apply Below
We design connected hardware and write the software behind it. This role sits where those two meet, so the same person takes a circuit from schematic through firmware to the rig that tests it.
Most of our hardware work arrives half-finished. There's a board from a vendor, a firmware contractor who has moved on, and a cloud team still waiting on device data. Getting those three to agree with each other is usually the job before anything can ship.
What you would work on:
- Schematic capture and board layout for sensor, power, and microcontroller circuits, rigid and flex, with revisions driven by what the bench and the firmware tell us.
- Production firmware in C++ on modern 32-bit microcontrollers, most recently Renesas and Arduino parts, covering sensor drivers, calibration and self-test routines, event detection, alarm handling, and the protocols the device speaks.
- Timing work on multi-channel analog front ends, where the shape of the acquisition loop decides whether the data is good enough to act on.
- Over-the-air updates for constrained parts. That means owning how an image is packaged and shrunk, how a device works out which build applies to it, and how a release reaches one unit before it reaches the fleet.
- Radio bring-up, plus the connectivity the device speaks to the outside world over BLE, WiFi, and MQTT.
- Battery and low-power work, from charge behavior and state-of-charge monitoring through to sleep modes and the rails that stay energized when you thought they were off.
- Design review of vendor deliverables. We read a package for BOM completeness, clean rule checks, and connector and harness detail, then write up what has to change before anything gets fabricated.
- Manufacturing handoff, which means schematics and layout files, BOM and Gerbers, assembly and test notes, hardware-in-the-loop rigs, and the flash and provisioning scripts a contract manufacturer builds from.
- Regulatory groundwork alongside the design, covering radio certification and the conditions that come with a pre-certified module, plus environmental and vibration qualification.
What we look for:
- You've shipped firmware that went into production on a real product, and you can talk about how it behaved in the field.
- You're fluent in C and C++ on bare metal or a thin RTOS, and you'll open a datasheet when you need I2C, SPI, or UART to behave.
- You read schematics and lay out boards yourself, and you have views on grounding, decoupling, and connector choice that you can defend.
- Analog and mixed-signal front ends are familiar ground, and you know what a calibration has to prove before a unit leaves the bench.
- You've taken a design through a contract manufacturer at least once and know what they need from you and when.
- You write clearly. A good share of this work is telling a client, in writing, exactly what's wrong with a deliverable and what it will cost to fix.
Nice to have:
- Renesas RA, Nordic nRF, STM
32, or Espressif parts. - Multilayer stackups, impedance control, and EMC work.
- Motor control, power electronics, or RF design.
- Test fixtures and calibration tooling, including the software an operator runs on the production floor.
- Battery shipping classification work such as UN 38.3.
- Embedded Linux, Yocto, or A/B update systems, since our device work spans both ends.
- Quick-turn prototype assembly and overseas part sourcing.
To View & Apply for jobs on this site that accept applications from your location or country, tap the button below to make a Search.
(If this job is in fact in your jurisdiction, then you may be using a Proxy or VPN to access this site, and to progress further, you should change your connectivity to another mobile device or PC).
View / Apply for Jobs
Matching My Jurisdiction
(If this job is in fact in your jurisdiction, then you may be using a Proxy or VPN to access this site, and to progress further, you should change your connectivity to another mobile device or PC).
View / Apply for Jobs
Matching My Jurisdiction