Journeyman Sheet Metal Worker

The Journeyman Sheet Metal Worker (Cladding) performs sheet metal fabrication, assembly and installation work on travel-based construction projects. The work is focused on non-HVAC sheet metal applications, including insulation, insulated metal panels, flashing, trim, siding, metal wall system sand custom sheet metal components.

This is a journeyman-level travel position. The Journeyman Sheet Metal Worker is expected to work independently to project drawings and specifications, coordinate with foremen and project supervision, and complete work accurately, safely and according to project specifications.

MECO does not perform HVAC work. This position is not intended for candidates whose experience is limited to HVAC ductwork unless they also have relevant sheet metal, panel, insulation, siding, flashing ormetal wall system experience.

• Fabricate sheet metal components.
• Cut,shape, drill, fasten and assemble sheet metal materials.
• Install insulated metal panels and insulation.
• Install flashing, trim, siding and metal wall systems.
• Install custom sheet metal components.
• Perform repairs or replacement of existing sheet metal installations.

• Measure and lay out materials based on drawings and field conditions.
• Workfrom lifts, ladders, scaffolds and elevated work areas.
• Assemble and disassemble scaffolding systems.
• Coordinate with foremen, project managers and other supervisors.

• Work safely and follow all MECO, OSHA and site safety requirements, including the use of fall protection.
• Usehand tools, power tools, lifts and fastening systems safely and keep tooling in good working condition.

• Assist with or maintain basic jobsite records, such as scaffold material used,quantities or safety documentation, as directed by the foreman or supervisor.
• Signoff on daily timesheets and ensure time is recorded accurately.

• None.
  
  May provide on-the-job direction to sheet metal helpers as assigned by the foreman.

The employee is required to provide their own standard sheet metal hand tools, including:

• Hammerand rubber mallet
• Tape measure (25’–35’)
• Levels(torpedo and 2’ minimum)
• Chalkline
• Aviation snips (left, right and straight)
• Utility knife
• Sheet metal hand seamer
• Straightedge or framing square
• Cordless drill/driver and impact driver
• Drillbits suitable for metal
• Nut drivers
• Rivetgun
• Caulking gun
• Toolbelt/bag

The employee must also provide a hard hat, fall protectionharness and leading-edge self-retracting lifelines. Tooling must be in good working condition and appropriate for construction work. MECO will provide major equipment, power tools, consumables and job-specific materials unless otherwise stated.

• Minimumof five (5) years of non-HVAC sheet metal installation experience.
• Experience with insulation and insulated metal panel installation.
• OSHA
  10 certification.
• Experience with power tools, lifts, ladders, scaffolds, fastening systems and fall protection systems commonly used in industrial sheet metal installation.
• Abilityto operate JLGs, scissor lifts, aerial lifts and other necessary equipment.
• Abilityto read and work from drawings and field measurements.
• Abilityto use sheet metal hand tools and power tools safely and effectively.
• Bilingual (Spanish)
• Abilityto follow instructions.
• Abilityto travel out of state for project assignments.
• Reliable transportation.
• Mustbe legally authorized to work in the United States.
• Abilityto pass a 10-panel hair follicle drug test.

The successful Journeyman Sheet Metal Worker should demonstrate accuracy, attention to detail, safe work habits, dependability andthe ability to work independently while coordinating with the crew, foremen and project supervision.

This position performs work on active construction sites,outdoors and in varying weather conditions, including heat, cold, noise anddust. The employee must be able to work at heights and in physically demanding environments, including from lifts, ladders, scaffolds and elevated work areas,and must be able to lift at least 50 pounds individually.

The position is travel-based and requires out-of-state travel for project assignments. The employee must wear required personal protective equipment and follow all site safety requirements.

Reasonable accommodations may be made to enable qualified individuals with disabilities to perform the essential functions of the position.