Electrician

Fusion Solutions is looking for a team of electricians to install and commission conveyor belts in Radnor, OH and West Jefferson, OH. Details listed below. Please let me know a good time to connect if interested. Feel free to send me a copy of your resume at M or call at:

Title:

Journeyman and 2 – 3 Certified Electrician

Location:

Radnor, OH and West Jefferson OH

Work Done at a Staging Sites in Radnor and then commissioning done in West Jefferson after a week or two

1 week: 4 – 5 days at staging sites / testing

And then 2-3 days for commissioning on Site in West Jefferson

Start:
Mid-June 3, 2026

Duration: 1 month project

• The contractor shall wire all equipment in accordance with the attached drawing set. All wires and cables
• shall be properly identified at all termination points.
• The contractor shall supply all wire, conduits, connectors, terminal blocks, hole seals, pull boxes,
• and other equipment required for complete installation unless otherwise stated in this document.
• All wire terminations shall be made by the contractor in a neat and professional manner that is acceptable to our company.
• A maximum connection of two wires per terminal screw.
• Ring type crimp lugs shall be used for wires greater than 110V when the equipment supports it.
• Wire number labels shall be applied to all wires at each end. If part of a multiconductor cable set the cable shall be labeled at each end.
• All terminations should follow the schematics and labeling conventions.
• Wire labels shall be adhesive self-laminating wrap around. Wire numbers shall be legible from all sides.
• Label Devices in the field consult our associate on-site for label positioning.
• Any deviations from the electrical installation documents provided must be approved by the engineer prior to use.
• All work areas must be kept clean.
• The contractor shall install all conduit, wire, and cable in accordance with the 2023 NEC and our company standards.

• See pull schedule for cable routing, cable labeling, and wire labeling
  • Mount Sensors
  • Sensors and Valves will be terminated with single ended cord set M12 to Flying Leads
  • Route and terminate cables from I/O to Junction Boxes
    • Photo-eyes, Proximity Sensors, Reed Switches, Valves, etc.
  • Route and terminate cables from I/O to the Operator Panel
    • Photo-eyes, Proximity Sensors, Reed Switches, Valves, etc.
    • Key Switch 1
    • Gate Switch 1
  • Route and terminate cables from MCP
    • Load Conveyor 2 Pusher Servo (last 3.5 meter through drag chain)
    • Key Switch 2
    • Gate Switch 2
  • Route and terminate cables from the Remote Servo Panel
    • Load Conveyor 1 Pusher Servo (last 3.5 meter through drag chain)
  • Tear down for shipping. Organize cables to be palletized with the enclosures.
    • Utilize M12 QD connections to pull back sensor and actuator cables.
      • Pull back to closest Junction Box or Operator Panel
    • As needed, some cables may not need to be disconnected based on delineation for mechanical unit teardown.
  • Determine and pull multi-conductor cables to the MCP
    • Junction Boxes and Operator Panel
  • Determine and pull the 3phase cables back to the MCP
  • Disconnect and pull the servo cables to their respective enclosure
  Install for Commissioning – West Jefferson, OH
  • Final Drop and termination for the MCP Feeder conductors
  • Customer will supply conduit for the system. 1-1.5” conduit anticipated, to be determined before installation.
  • The installer shall provide the appropriate Fittings, Tees, Hole Seals, Flex Conduit to complete the installation.
  • The installer shall mount conduit to fence, floor, or equipment as specified by the customer
  • Servo power cables shall be run through conduit. Flex conduit shall be used for the final 48” run using a cable gland. Support the flex conduit. The servo is terminated with a connector and does not have threads for accepting conduit fittings.
  • Three-phase power to the Hydraulic Power Unit and the Remote Servo Panel shall be run through conduit. Flex conduit can be used for the final 48” run.
  • Re-route and terminate the cables from teardown.
  • Route and terminate cables associated with each of the 3rd party lathes
  • Process Interlocks Cables
  • Safety Interlock Cables
  • Ethernet Cables
  • CNC Machine Door Switch
  • 1 electrician 1 day (up to 8 hours) to support I/O checkout and debug