Field Service Technician

Field Service Technician

The role will be based out of Corpus Christi, TX, work in the Permian, and travel across the area! Job Summary

We are seeking a highly skilled Field Service Technician to support the installation, commissioning, maintenance, and troubleshooting of oil & gas measurement and automation systems, including LACT units, meter skids, NGL skids, and gas meter runs.

This role requires a strong foundation in electrical, instrumentation, and mechanical systems, along with the ability to diagnose complex field issues, improve system reliability, and deliver high-quality service to customers in demanding field environments.

The ideal candidate thrives in a fast-paced, hands-on environment and is committed to safety, precision measurement, and continuous improvement.

Measurement Systems & Equipment

Install, commission, and start up:

• ACT (Lease Automatic Custody Transfer) units
• Crude oil, produced water, and NGL meter skids
• Gas meter runs (orifice, ultrasonic, Coriolis, thermal mass)
• Perform meter proving, calibration, and system validation in accordance with API and AGA standards
• Troubleshoot and repair:
• Flow meters (Coriolis, ultrasonic, turbine, PD)
• Control valves, regulators, and back pressure valves
• Pumps, motors, and mechanical components
• BS&W equipment, sampling systems, and analyzers

Electrical, Controls & Instrumentation

• Install, commission, and troubleshoot:
• Electrical systems (up to 480V), MCCs, and control panels
• PLCs, RTUs, flow computers, and HMI systems
• VFDs, transmitters (pressure, temperature, flow, level), and I/O systems

Diagnose faults using:

• Multimeters, megohmmeters, and diagnostic tools
• Electrical schematics, loop diagrams, and P&IDs
• Ensure proper grounding, bonding, and compliance with electrical and safety standards

Field Service & Customer Support

• Respond to scheduled and emergency service calls across the Permian Basin
• Execute work safely using LOTO, JSAs, permits, and energized work procedures
• Interface directly with customers, providing technical expertise and professional service
• Generate detailed service reports including:
• Root cause analysis
• Failure modes
• Corrective actions and recommendations

Reliability & Continuous Improvement

• Perform preventative and predictive maintenance to reduce downtime
• Identify recurring failures and drive root cause solution

Contribute to:

• Standard work development
• Troubleshooting guides and checklists
• First-time fix rate improvements

Support a Lean, safety-first culture focused on:

• Reducing variation
• Improving uptime
• Enhancing service quality

Experience:

• 5+ years of field service experience in oil & gas, measurement, or industrial environments

Strong knowledge of:

Industrial electrical systems (480V and below)

Measurement systems and instrumentation

Ability to read and interpret:

• P&IDs
• Electrical schematics and loop diagrams

Experience working independently in remote field locations

Valid driver's license required, with the ability to maintain a clean and safe driving record.

Preferred Qualifications

• Experience with LACT units, meter skids, or gas measurement systems
• Flow computer experience (ABB, Emerson ROC & FB3000, OMNI, WAGO, etc.)
• PLC/HMI experience (Allen-Bradley, Siemens, IDEC, Red Lion, Beijer, etc.)
• VFD experience (ABB, Danfoss, Rockwell, Schneider, LS, Benshaw, etc.)
• Familiarity with API and AGA standards
• Certifications:
  
  OSHA 10/30, H2S, Safeland/PEC, Arc Flash, TWIC
• Lean / Six Sigma or reliability experience

Education and Training

• High School Diploma or GED required
• Technical or vocational training in Electrical, Instrumentation, or Industrial Maintenance preferred
• Equivalent field experience or 5–10 years in a similar technical role accepted.

Work Environment & Requirements

• Frequent travel across the Permian Basin, STX, SE NM. (up to 90-95%)
• Work outdoors in extreme conditions (heat, cold, dust, wind)
• Regularly lift and/or move up to 25 lbs. (12 kg); frequently up to 50 lbs. (23 kg); and occasionally up to 100 lbs. (45 kg). (Above 100 lbs. help will be required)
• Climb ladders, structures, and equipment

Willingness to work:

• Overtime
• On-call rotations
• Nights, weekends, and holidays as needed
• Compliance with all company policies, including Drug & Alcohol policy.
• Ability to work safely and collaboratively.
• Must be authorized to work in the United States.

What We Offer

• Competitive hourly pay + overtime
• Company vehicle, tools, and test equipment
• Per diem (if applicable)
• Medical, dental, vision, and 401(k)
• Ongoing technical and safety training
• A strong culture focused on safety, measurement…