Heat Operator 2nd Shift- Gear and Shaft

Position: Heat Treat Operator 2nd Shift- Gear and Shaft
Eaton’s AER FMC Fuel Motion Control Systems division is currently seeking a Heat Treat Operator 2nd Shift
- Gear and Shaft at our Euclid, Ohio facility. Core hours for 2nd shift are 3:30pm - 12am Monday - Friday.

The hourly rate for this position is $28.98 plus $1 shift premium per hour.

Please note the salary information shown above is a general guideline only. Salaries are based upon candidate skills, experience, and qualifications, as well as market and business considerations.

What you’ll do:

Set up and operate various burring, cleaning, buffing and blasting machines to generate rough and finish dimensions on a variety of parts. Perform operations such as nitride, heat treat, buff and blast. Also perform hand operations required to burr, polish, finish, and blend surfaces on machined parts.

Perform visual and dimensional inspections and maintain accurate documentation on a variety of parts in accordance with ANSI Y14-5 and the Certified Operator program.

Assistance may be given to other operators on proper operational procedures.

Load, unload and monitor processing of parts in heat treat basket, load furnaces, operate furnaces, monitor gages, unload furnaces, and perform hardness test.

Perform various burr, buff, dry blast, degrease and oiling operations on hardware.

Set up, operate, monitor, read, interpret, and maintain furnace, atmosphere generation, and quench equipment controls and instruments such as timers, temperature control and monitoring recorder charts, flow scopes, pressure gages, various dial gages. Instruments may be analog or digital (programmable microprocessor) based.

Set up and operate all equipment with a minimum of assistance, be familiar with work procedures involved with nitride, heat treating, and buffing operations. Frequent changes in set-up and maintenance of close tolerance require constant attention.

Mount and accurately align various jig and fixtures, select speeds, and feeds. Load and align tooling working from engineering layouts. Adjust stops and cams to produce finish dimensions to tolerances.

Read and interpret moderately complicated blueprints and execute quality checks using a variety of mechanical and electronic gages.

Maintain accurate lot control (QCP 6.0) traceability, record keeping, log book entries, NCR’s (QCP 11.0) and associated documentation. *(Reordered)
Generate close tolerance edge breaks using various hand tools.

Maintain clean equipment and work area, Perform minor machine maintenance as needed.

Chart and plot data per SPC requirement.

Move material within the cell.

Qualifications:

Required Qualifications:

High School Diploma or GED from an accredited institution.

Must reside within a 50-mile radius of Euclid, Ohio; no relocation benefit is provided.

This position requires access to export-controlled information. To conform to U.S. Government export regulations applicable to that information, applicant must be a U.S. person, defined as a (i) U.S. citizen or national, (ii) U.S. lawful, permanent resident (green card holder), (iii) refugee under 8 U.S.C. 1157, or (iv) asylee under 8 U.S.C. 1158.Minimum one (1) year of machining/utility, heat treat or nitride experience.

Minimum 2-year GD&T Experience (successful completion of Eaton Level 1 Advanced Training will be considered in lieu of this requirement).

Skills:

Position Criteria:

Pass an Eaton vision test.

Become a Certified Operator.

Perform 5S and other duties as assigned.

Complete Basics of Measurement courses

Blueprint Reading 131

Math Fundamentals 101

Math:
Fractions and Decimals 111

Units of Measurement 112#LI-CD1#IND
123

Safety Sensitive Position – Drug & Alcohol Testing This position is classified as a safety sensitive role under applicable U.S. Department of Transportation (Use the "Apply for this Job" box below). Federal Aviation Administration (FAA) regulations. As a condition of employment, candidates must successfully complete a DOT required pre employment drug test.

Individuals hired into this role remain subject to ongoing drug and/or alcohol testing, including random testing, in accordance with federal regulations. Eaton maintains a drug and alcohol free workplace and expects all applicants to understand and comply with these…