Instrumentation Technician - Intermediate

Location: Lemont

* Install, operate, inspect, troubleshoot, repair, calibrate/adjust, and maintain the following equipment including but not limited to:
* Maintain and/or prepare reports and/or records including but not limited to:  + Maintenance and repair records  + Safety and environmental reports  + Mechanical drawings  + Electrical schematics and diagrams  + Pressure readings  + Material and supply orders  + Loop sheets
* Responsibilities may include Department of Transportation (Use the "Apply for this Job" box below). functions, including operations, calibration documentation, maintenance, or emergency response on a pipeline. Job duties also require the employee to be alert and respond immediately to dangerous or hazardous conditions, and where impaired performance, or failure to follow safety precautions, could result in serious injury or property damage.
* Gravitometers/Densitometers
* Chromatographs* Telemetering systems
* Moisture analyzers
* ESD systems
* Electronic odorization systems
* AC Power distribution systems - single phase and three phase: 120V, 240V, 480V, 4160V
* Motors* Switchgear
* VFDs* Soft starters
* 24V DC systems
* Instrumentation* Flow computers
* Pressure transmitters
* Level transmitters
* Flow transmitters
* Temperature transmitters
* Thermocouples* Meter tubes and orifice plates
* Satellite equipment
* Analytical equipment
* Supervisory Control and Data Acquisition (SCADA) system and remote terminal units and equipment
* Distributed Control System (DCS)
* Programmable Logic Control (PLC) systems
* Perform preventative maintenance and/or analytical testing on compressors/engines, drivers, and auxiliary equipment
* Maintain electrical power circuits, switch gear, and power distribution
* Install and maintain security/intrusion systems
* Drive and ensure maintenance is complete on company vehicle
* Experience reading and interpreting repair orders, mechanical drawings, procedures, charts, diagrams, dials, gauges, and equipment manuals
* Experience preparing, processing, or verifying maintenance and repair records, safety and environmental reports, electrical schematics and diagrams, pressure readings, and material and supply orders
- Experience in use and function of tools and equipment applicable to position including but not limited to:  
* Manual/power tools  
* Electronic testing devices such as DVOM, amp clamp, and mega ohm meter  
* Control devices
- Experience and training related to:  
* Gas processing fundamentals  
* Computers and related software  
* Governmental rules, regulations, and (electric) codes  
* Company policies and procedures including safe handling practices for flammable gases, liquids, and high pressure systems  
* Reliability Based Programs
* Knowledge of: the use and function of reciprocating or gas turbine engines, compressors, and electronic and processing equipment applicable to position
* Knowledge of: instrumentation, electronics, tools and control systems
* Ability to: apply addition, subtraction, multiplication, division, and algebraic formulas
* Ability to: communicate and/or exchange written and verbal information and instructions
* Standing:
Remaining on one's feet in an upright position at a work station without moving about (Frequently)
* Walking:
Moving about on foot (Frequently)
* Sitting:
Remaining in a seated position (Occasionally)
* Lifting:
Raising or lowering an object from one level to another (includes upward pulling) (Occasionally)
* Carrying:
Transporting an object, usually holding it in the hands or arms, or on the shoulder (Occasionally)
* Pushing:
Exerting force upon an object so that the object moves away from the force (Occasionally)
* Pulling:
Exerting force upon an object so that the object moves toward the force (includes jerking) (Occasionally)
* Climbing:
Ladders, Stairs (Occasionally)
* Balancing:
Maintaining body equilibrium to prevent falling (Occasionally)
* Stooping:
Bending the body downward and forward by bending the spine at the waist (Occasionally)
* Kneeling:
Bending the legs at the knees to come to rest on the knee or knees (Occasionally)
* Crouching:
Bending the body downward and forward by bending the legs and spine (Occasionally)
* Crawling:
Moving about on the hands and arms in any direction (Occasionally)
* Reaching:
Extending hands and arms in any direction (Constantly)
* Handling:
Seizing, holding, grasping, turning or otherwise working with the hand or hands (Manual Dexterity) (Constantly)
* Fingering:
Picking, pinching or otherwise working with the fingers primarily (Finger Dexterity) (Constantly)
* Feeling:
Perceiving such attributes of objects/materials as size, shape, temperature, texture, movement or pulsation by receptors in the skin, particularly those of the finger tips (Constantly)
* Talking:
Expressing or exchanging ideas/information by means of the spoken word (Frequently)
* Hearing:
Perceiving the nature of sound by the ear (Frequently)
* Tasting/Smelling: (Constantly)
* Near Vision:
Clarity of vision at 20 inches or less (Constantly)
* Far Vision:
Clarity of vision at 20 feet for more…