Sr Braider Operator - 1st shift Job Mansfield area,Texas USA,Manufacturing / Production

Position Summary

This 1st shift Senior Braider Operator will operate and setup TMW-3deck and TMW-4deck braiders and monitor for proper product quality.

Responsibilities

Know how to operate NEB, OMA, TMW 24/36 braiders and train entry level braider operators as needed

Pull tooling and materials according to manufacturing specifications for applicable machine(s), such as springs, braid rings, tube guides, wound bobbin, core tube, etc.

Inspect tooling before using and track material used in WW3 system and Braider Logs

Set up applicable machine(s) according to manufacturing specifications (braid ring height, install tube guide, change deck/puller gear, unload/load carriers, unload/load bobbins, etc.)

Identify correct mandrel size for the core tube to help guide through machine, rotate mandrel till job finishes and strip when done, resize and rework as needed

Mark defects and new preforms with the correct tape color

Measure and record OD and pitch on Hose Process Chart (SPC) for all deck levels

Perform inspection of carriers and know how to rebuild

Perform pull test on all aerospace hose

Replace oil barrels when needed

Set completed hose to proper staging area

Maintain work area in clean and orderly fashion, follow 5s practices

Know and practice all safety regulations and quality guidelines

Report production issues to Direct Lead

Perform work of an equal or lower classification

Department Specific / Non‑Essential Functions

Work safely in accordance with regulations, standards, and procedures, and in a manner that eliminates unreasonable risk to health and the environment. Notify management of unsafe conditions or practices, unlawful activities and activities which present unreasonable health and/or environmental risk. Report all safety and/or environmental incidents to management immediately.

Prevent excess waste of product and/or components by operating the equipment in an efficient manner.

Participate in peer‑based teams (i.e., Natural High Performance Teams), and work with groups to initiate and implement programs such as Lean Manufacturing and 5‑S.

Other duties may be assigned at a later time.

Qualifications

Education:

High School diploma or GED
Experience:

Production work preferred but not required
Preferred Skills/

Qualifications:
Good verbal and interpersonal communication skills
Basic knowledge and use of hand tools
Sound decision making skills
Good math, reading, writing skills
Demonstrated mechanical aptitude
Strong trouble shooting skills
Be able to exercise continuous mental, visual, and audio attention
Ability to work well in a team environment
Skills/

Competencies:
Basic computer skills
Ability to monitor machine sounds to identify and diagnose changes inorder to take appropriate action.
Vision:
Near acuity and accommodation for reading information to perform job tasks.
Requires constant alertness to surroundings and product quality with attention to detail.
Must be able to demonstrate ability to operate department equipment (i.e. NEB braiders, TMW and OMA braiders, etc.)
Must be able to read work orders and interpret manufacturing specifications.
Ability to use and interpret measuring instruments (i.e. calipers, micrometers, pi tape, etc.)
Physical Requirements:
- Lift/Carry up to 10 lbs
- Lift/Carry up to 20 lbs
- Lift/Carry up to 30 lbs
- Bending
- Twist/Turn
- Reach Below Knee
- Push/Pull
- Squat/Kneel
- Stand/Walk
- Sit
- Lifting Above Shoulders
Assessment:
Employee must pass Pre‑employment screening

Organizational Relationships / Scope

Report directly to Value Stream Team Leader
Work closely with Maintenance to resolve issues with the equipment

Working Conditions

The employee may be subject to:

High noise levels from operating machines and equipment.
Physical hazards from operating machines

Work in areas where safety equipment will be required (steel toe shoes, eye protection, hearing protection)

Standing is required for extended periods of time. Walking, pushing, pulling, reaching, bending, turning, twisting, squatting, and lifting is performed on a regular basis

Requires high degree of manual dexterity, which could be performed under restrictive conditions

Requires flexible hours and short notice for overtime.

The employee may be required to follow other…