Hose Coil \​/ Pressure Test Operator (PAF

Hose Coil / Pressure Test Operator

Temp to hire
- Pay: XXXXXXXXXXX/hr + shift differential XXXXXXXXXXX - XXXXXXXXXXX/hr

2nd shift (3:30 PM – 11:30 PM) - (Mon-Fri) - MANDATORY OT

Hose Coiling:

• Review conformance of hose while coiling on reel and cut hose as needed
• Verify part number, hose size and job numbers based on manufacturing specifications
• Review dimensions, tag colors and take up reel diameter
• Inspect product of attributes (flaws) such as bony hose, broken wires, missing wires, kinked hose, etc.
• Properly tape and cut out nonconforming sections of hose
• Place hose scrap in proper containers
• Record attributes (flaws) and hose scrap on Hose Coiling Inspection Sheets, update WW3
• Measure OD,  pitch
• Prepare and complete proper labeling of hose
• Cut burst and periodic samples as required
• Clean plug gages as needed

Pressure Test:

• Set up test mode (proof and/or impact), jaws, mandrels, prefill, run cycle time and dump pressure (purge) according to manufacturing specifications
• Record PSI impact on back of tag
• Cut off hose ends and wrap with tape
• Place tested hose in quality inspection area

Hose Coiling & Pressure Test:

• Maintain work area in clean and orderly fashion, follow 5S practices
• Know and practice all safety regulations and quality guidelines
• Report production issues to Direct Lead
• Perform work of an equal or lower classification

• Work safely in accordance with regulations, standards, and procedures, and in a manner that eliminates unreasonable risk to health and the environment. Notify management of unsafe conditions or practices, unlawful activities and activities which present unreasonable health and/or environmental risk. Report all safety and/or environmental incidents to management immediately.
• Prevent excess waste of product and/or components by operating the equipment in an efficient manner.
• Participate in peer-based teams (i.e., Natural High Performance Teams), and work with groups to initiate and implement programs such as Lean Manufacturing and 5-S.
• Other duties may be assigned at a later time

Education required:

- High School diploma or GED

Experience:

- Production work preferred but not required. On the job training from 1 to 8 weeks or extend to 10 weeks if needed.

Good verbal and interpersonal communication skills. Sound decision making skills. Good math, reading, writing skills. Be able to exercise continuous mental, visual, and audio attention. Ability to work well in a team environment.

1. Basic computer skills.
2. Ability to monitor machine sounds to identify and diagnose changes in order to take appropriate action.
3. Vision:
Near acuity and accommodation for reading information to perform job tasks.
4. Requires constant alertness to surroundings and product quality with attention to detail.

None at All(0%)Occasional(1-33%)Frequent(34-66%)Continuous(67-100%)Lift/CarryXUp to 10 lbsX
11-20 lbsX
21-50 lbsXBendingXTwist/TurnXReach Below KneeXPush/PullXSquat/KneelXStand/WalkXSitXLifting Above ShouldersX
- None at All(0%) - Occasional(1-33%) - Frequent(34-66%) - Continuous(67-100%) - Lift/Carry - X
- Up to 10 lbs - X - 11-20 lbs - X - 21-50 lbs - X
- Bending - X
- Twist/Turn - X
- Reach Below Knee - X
- Push/Pull - X
- Squat/Kneel - X
- Stand/Walk - X
- Sit - X
- Lifting Above Shoulders - X

Other

Skills:

Ability to work well in a team environment Has promotes a positive attitude

Assessment:
Employee must pass Pre-employment screening

• Report directly to Value Stream Team Leader
• Work closely with Maintenance to resolve issues with the equipment

The employee may be subject to:

• High noise levels from operating machines and equipment.
• Physical hazards from operating machines and moving reels.