Nondestructive TEST Inspector LEADER with Security Clearance

Position: NONDESTRUCTIVE TEST INSPECTOR LEADER with Security Clearance
Duties
* You will independently perform complex nondestructive testing and analysis on nonroutine mechanical components, piping systems, and structural assemblies related to Naval Surface Ships and submarines and nuclear propulsion plants.
* You will utilize the most advanced test methods and procedures in solving the most complex inspection problems.
* You will perform inspections on Nuclear Reactor Plant components and systems such as coolant system and pressurizing piping, pumps and valves, heat exchangers, and steam generators, as well as other critical ship systems.
* You will make a wide range of critical decisions on matters concerning the acceptance or rejection of work performed by highly skilled craftsmen and other inspectors, independent of and without consultation with a supervisor.
* You will acquire and record test results and data using enhanced signal processing and acquisition software on state-of-the-art computer based platforms.
* You will perform calibration and safety checks of test equipment prior to and after performance of NDT inspections. Requirements Conditions of employment
* Must be a US Citizen.
* Must be determined suitable for federal employment.
* Must participate in the direct deposit pay program.
* New employees to the Department of the Navy will be required to successfully pass the E-Verify employment verification check. To learn more about E-Verify, including your rights and responsibilities, visit e-verify.gov
* Within the Department of Defense (DoD), the appointment of retired military members within 180 days immediately following retirement date to a civilian position is subject to the provisions of 5 United States Code 3326.
* Males born after 12-31-59 must be registered for Selective Service.
* Successful completion of a pre-employment drug test (including marijuana) is required. A tentative offer of employment will be rescinded if you fail to report to the drug test appointment or fail the test. You will be subject to random testing.
* You will be required to obtain and maintain an interim and/or final security clearance prior to entrance on duty. Failure to obtain and maintain the required level of clearance may result in the withdrawal of a job offer or removal.
* You will be required to wear personal protective equipment such as helmets, gloves, coveralls, glasses, goggles, respirators and safety shoes continuously for the duration of the work shift
* Work is performed in areas where potentially harmful physical and chemical agents are present (e.g. fumes, dust, heat, ionizing and non-ionizing radiation and chemicals). You will be required to participate in medical surveillance programs.
* This position may require travel from normal duty station to CONUS and OCONUS and may include remote or isolated sites. You must be able to travel on military and commercial aircraft for extended periods of time.
* You will be required to obtain and maintain a current nondestructive test inspector certification. Qualifications Although a specific length of time and experience is not required for most trade and labor occupations, you must show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying.

Qualification requirements emphasis is on quality of experience, not necessarily the length of time. Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the job elements and screen out listed below. This job has a screen-out element which will be used to determine minimum eligibility for this job. Applicants who do not receive a minimum of two points on the screen-out element(s) will be found ineligible.

The Screen-out Element for this position is: ABILITY TO LEAD OR SUPERVISE
* Ability to obtain certification as an NDT inspector in the following methods: VT (Visual Inspection), PT (Liquid Penetrant Inspection), MT (Magnetic Particle Inspection) as well as the following major NDT method: UT (Ultrasonic Shearwave Inspection),or ET (Eddy Current Analysis Inspection), or RT (Radiographic Film Interpreter) or RIC (Radiographer In Charge).
* Ability to utilize a wide array of highly sophisticated quality control inspection/ NDT techniques;
* Ability to utilize unique and specially designed precision instruments and gauges;
* Ability to interpret complicated written technical material such as instructions, TGI's, specifications, procedures, sketches, and blueprints.
* Ability to independently interpret and analyze inspection test results and determining final acceptance/rejection of items in accordance with specific codes.
* Ability to participate in audits and prepare charts and status reports on progress while inspections are being completed. Applicants must meet the requirements of the Office of Personnel Management (OPM) Job Qualification Handbook for Trades and Labor Occupations. Additional…