Calibration​/Metrology Technician

Calibration / Metrology Technician

As the Calibration / Metrology Technician
, you will be responsible for the calibration and repair of precision Measuring and Test Equipment (M&TE), Test Measurement & Diagnostic Equipment (TMDE), and instrumentation in a Standards Laboratory and/or on‑site field environment. Applies engineering or technical experience to ensure that instruments are properly functioning and verifies performance against established specifications (accuracy, precision, etc.). Performs verification, adjustments, troubleshooting and repair of instruments and interfaces frequently with Metrology Engineers and equipment owners regarding calibration requirements, specifications, tolerances, etc.

Applies metrology techniques and theory to laboratory practices (linearity, hysteresis, bias, etc.) and uses basic math/algebra, scientific notation, and unit conversions between metric & Imperial/British units of measure. Exercises independent judgment in tasks such as problem solving, troubleshooting, analyzing circuits, and schematic & wiring diagrams.

• Requires demonstrated work experience in calibration and metrology principles as applied to multiple measurement disciplines including:
  Pressure & Vacuum:
  Analog & digital pressure/vacuum gauges, 4 mA to 20 mA transmitters, bourdon tubes, Pirani gauges, manometers, barometers, capacitance diaphragm gauges / CDG’s, Dead Weight Pressure Standards (Piston Gauges), Pressure Controllers, pressure regulators, vacuum pumps/chambers, etc.
• Temperature & Humidity:
  Thermometers (Liquid in Glass, Platinum Resistance Thermometers / PRT’s, Standard PRT’s, Industrial PRT’s, thermistors, thermocouples, Infra‑Red / IR, etc.), super‑thermometers or resistance bridges using ITS‑90 Coefficients, data loggers, transmitters, temperature fixed point cells (e.g. water triple point, etc.), fluid baths, dry block calibrators, temperature & humidity chambers, chilled‑mirror humidity standards, dew point, etc.
• Electrical Calibration:
  Digital multimeters (DMM’s), process calibrators, multifunction/multiproduct calibrators, conductivity meters, frequency standards, resistance decade boxes, standard resistors, current clamps, power supplies, current shunts, signal generators, oscilloscopes, tachometers, etc.
• Flow:
  Flowmeters, rotameters, anemometers, flow standards & laminar flow elements (e.g., Mol Box & Mol Blocs), thermal mass flow, sonic nozzles, wind tunnels, centrifugal air samplers, etc.
• Dimensional:
  Gauge blocks, micrometers, calipers, pin gauges, go/no‑go gauges, vision machines (OGP, etc.), Coordinate Measuring Machines (CMM’s), supermics, laser ruler / interferometer, surface plates, torque wrenches, load cells, height gauges, drop gauges, etc.
• Knowledge or experience is desirable with any of the following software applications: IBM Maxmio, Fluke Met/Cal, Fluke COMPASS, Mettler Calibry, Mettler MC‑Link, etc.
• Knowledge of any of the following is desirable:
  Precision Measurement Equipment Laboratories (PMEL), industry standards such as ISO 17025, ANSI Z540.1 & Z540.3, ISO 9001, NCSL Recommended Practices, measurement uncertainty (ISO GUM), concepts such as Test Uncertainty Ratio (TUR) and Test Accuracy Ratio (TAR), Repeatability & Reproducibility, Gauge R&R, Measurement System Analysis (MSA), statistics, quality control charts, Out of Tolerance (OOT) investigation and OOT impact analysis.
• Manages workload efficiently in a fast‑paced, team environment, with high attention to detail, while practicing Current Good Manufacturing Practices (cGMP) in an FDA regulated environment

• High School diploma or GED required. Minimum of 4 years’ experience as a Senior Instrument Technician or the equivalent. Associates Degree in electronics technology or equivalent is strongly desired. College coursework and/or ASQ Certified Calibration Technician (CCT) certificate a plus.
• Experience with analytical instruments is a plus, e.g., Analytical Balances, High Performance Liquid Chromatography (HPLC), Gas Chromatography (GC), Mass Spectrometry (MS), Ultra‑Visible Spectroscopy (UV‑Vis), etc.
• Must manage activities to meet restrictive timelines. Must have skills in…